OBC_11KW_Three-phase 304 ~ 456VAC (line-line voltage,three-phase four-wire)Single-phase 176 ~ 264VAC, 250~450VDC, Three-phase: 32A, 3.3KW single phase: 10A, 6.6KWsingle phase: 20A_Module
Model No.:LWC11K-380S380-M
Power:11KW
Input Voltage:Three-phase 304 ~ 456VAC/Single phase 220 ± 15% VAC
Output Voltage:250~450VDC
Efficiency:95%
Code LWC11K-380S380-M
Download: 11KW On Board Charger Module
Features
● Charging Standard: IEC
● Output Power：11KW
● Input Voltage：Three-phase 304~456VAC (L-L, three-phase four-lines) Single phase 176~264VAC
● Output Voltage：450~750VDC
● Dimensions：364x224x100mm
● Cooling System：Liquid
● IP Rating：IP67
● Communication：CAN-BUS
● Enclosure: Aluminum alloy made
● Software: Digital software design
Specification
| Description | Parameters | Remark | |
| Output Power | Three-phase 11KW / single-phase 3.3KW or 6.6KW | ||
| Input voltage range | Three-phase 304 ~ 456VAC (line-line voltage,three-phase four-wire)Single-phase 176 ~ 264VAC | ||
| Output voltage range | 250~450VDC | ||
| Low voltage (VDC) | 13.8VDC (5Amax) | ||
| Activation method | CP / CC / hard wire | ||
| Voltage accuracy | ±1% | ||
| Output maximum current | Three-phase: 32A, 3.3KW single phase: 10A, 6.6KWsingle phase: 20A | ||
| Voltage ripple coefficient | ≤±1% | ||
| Current accuracy | ±3% | Half load or more | |
| Efficiency | ≥95% | Rated voltage Full load | |
| Parallel function | Parallel networking through internal CANcommunication, supporting up to 8 modules inparallel. | ||
| Output response time | The rise time of the on-board charger outputvoltage should be less than 300ms, and theovershoot should be less than 10%. After receivingthe shutdown command, the current drops below10% in 300ms, and drops to 0A in 500ms. | ||
| Other protection features | Input over voltage, input under voltage, output overvoltage, output under voltage, short circuit, outputover current, over temperature, reverse connectionprotection, potential equalization and groundprotection, power failure protection | ||
| Over temperature protection | When the temperature reaches 85 ° C, the outputpower is halved, and the temperature is lower than 80 °C within 10 minutes, and the load is automaticallyrestored. After 10 minutes, the temperature is higherthan 80 ° C, then the power is turned off. When thetemperature is higher than 90 ° C, the power is turnedoff directly. | ||
| Dielectric strength | Output to outer casing | 2000VDC /60S 10mA Max | |
| Input to outer casing | 1500VAC /60S 10mA Max | ||
| Input to output | 3000VAC /60S 10mA Max | ||
| Insulation resistance | Input to output | ≥20MΩ | |
| Input to outer casing ≥ |
≥20MΩ | ||
| Electromagneticcompatibility | Radiation emission | GBT 18387：2008，EN 55022 CLassB | |
| Conducted emission | GBT 18387：2008，EN 55022 CLassB | ||
| Radiation immunity | GBT 18387：2008，EN 55022 CLassB | ||
Structural parameters
.jpg)
Vdc connector: 12V 200Amax
Wakeup signal connector
Connector information
| Item | Receptacle model | Funtion | Maker | Plug model |
| A | M4 stud | AC input | M4 screw OT terminal(Outer diameter is not greater than 7mm) | |
| B | M4 stud | DC outp | M4 screw OT terminal(Outer diameter is not greater than 9mm | |
| C | 105314-1216 | Signal control | Molex | Plug: 105308-1216 Pin: 105300-2200 |
| D | A2547WRB-2*4P | Internal parallelsignal base 1 | CJT | Plug: A2547HJ-2 * 4P Pin: A2547-GP |
| E | S2B-XH-A | Internal parallelsignal base 2 | JST | Plug: XHP-2 Pin: SXH-001T-P0.6N |
Pinout definition
| System Load definition | Pinnumber | Pinout definition | Description |
| AC input(M5 stud) | 1 | L1 | Firewire 1, 3PIN terminal, 16A MAX |
| 2 | L2 | Firewire 1, 3PIN terminal, 16A MAX | |
| 3 | L3 | Firewire 1, 3PIN terminal, 16A MAX | |
| 4 | N | Neutral line, metal terminal block, 32A MAX (Need to checkcarefully to prevent wrong connection.) | |
| 5 | PE | Protective ground point, grounded through the chassis. | |
| DC output(M4 stud) | 1 | VOUT+ | MAX 40A |
| 2 | VOUT- | MAX 40A | |
| Control terminal Receptacle: 105314-1216 Plug: 105308-1216 Pin: |
1 | VCC- | Normal input negative (2A) Voltage range: 9-32V |
| 2 | VCU_EN | Hard-wire wake-up and enable signals | |
| 3 | LOCK+ | Electronic lock power supply + | |
| 4 | LOCK- | Electronic lock power supply- | |
| 5 | LOCK FB1 | Electronic lock lock feedback 1 | |
| 6 | CANH | CAN1 high | |
| 7 | CANL | CAN1 low | |
| 8 | WAKE_UP | Output wake-up signal | |
| 9 | VCC+ | Normal input is positive Voltage range: 9-32V |
|
| 10 | CC_OUT | CC status output, low level enable | |
| 11 | NTC1- | Temperature sensor 1 negative | |
| 12 | NTC1+ | Temperature sensor 1 positive | |
| 13 | NTC2- | Temperature sensor 2 negative | |
| 14 | NTC2+ | Temperature sensor 2 positive | |
| 15 | CC | CC | |
| 16 | CP | CP | |
| Internal parallel signalbase (4PIN) |
1 | CANL2 | Internal parallel CAN2 low |
| 2 | CANH2 | Internal parallel CAN2 high | |
| 3 | TB_R | Termination resistor selection, the resistance is effective whenshorted to pin 2 | |
| 4 | EN2 | Internal parallel enable (reserved) | |
| 5 | NC | NC | |
| 6 | NC | NC | |
| 7 | NC | NC | |
| 8 | NC | NC | |
| Internal parallel signalbase 2 Socket: S2B-XH-A |
1 | EN_L+ | Host selection + |
| 2 | EN_L- | Host selection- |
Label
| Product Name | 11KW On Board Charger Module | ||
| Product Model | LWC11K-380S380-M | ||
| Code | LWC11K-380S380-M-AR01 | ||
| Serial Numbe | |||
| Input Voltage | Three-phase 304 ~456VACSingle phase 220 ±15% VAC | Output Voltage | 250~450VDC |
| Output Current | 32A | Output power | 11KW |
| Supplier | ANNREN TECHNOLOGIES CO., LTD. | ||
Add to cart
OBC_11KW_Three-phase 304 ~ 456VAC (line-line voltage,three-phase four-wire)Single-phase 176 ~ 264VAC, 250~450VDC, Three-phase: 32A, 3.3KW single phase: 10A, 6.6KWsingle phase: 20A_Module
Model No.:LWC11K-380S380-M
Power:11KW
Input Voltage:Three-phase 304 ~ 456VAC/Single phase 220 ± 15% VAC
Output Voltage:250~450VDC
Efficiency:95%